2019 - 2020 College Catalog
 Select a Catalog 2019 - 2020 College Catalog 2018-2019 College Catalog [ARCHIVED CATALOG]
Jun 04, 2020
2019 - 2020 College Catalog

# Electrical Construction and Instrumentation - AAS

SUNY Curriculum Code: 1642

HEGIS: 5317.00

## Minimum Total Credit Hours = 64

Notes:

• MATH 128 - College Algebra  is the minimum exit-level mathematics requirement for the AAS degree. Students with higher level mathematics backgrounds may choose to substitute courses in the Calculus sequence.

## Program Learning Outcomes

A graduate of the Electrical Construction and Instrumentation AAS program should be able to:

• Understand and discuss electrical theory and its practical application to electrical circuits and equipment, including the topics of electron theory, Ohm’s Law, types of electrical circuits, and concepts in direct-current circuits and electromagnetism.
• Design, plan, install, and maintain residential electrical equipment in accordance with the standards required by the National Electrical Code.
• Comprehend and interpret National Electrical Code regulations to ensure code compliance, and demonstrate the skills required to perform the necessary calculations.
• Demonstrate knowledge of the characteristics and applications of alternating-current theory from the point of production throughout its distribution, and use in single- and three-phase systems.
• Understand and apply the theory of electrical heating systems, low-voltage control systems, residential and commercial electrical systems, and motor control systems.
• Demonstrate the ability to plan, install, and maintain residential and commercial electrical systems.
• Design and draw wiring and schematic diagrams.
• Write sequences of operation for control systems.
• Demonstrate workmanship in electrical installations consistent with accepted industry practices.
• Demonstrate the ability to safely use common test equipment.
• Calculate electrical circuit configurations, including series, parallel, and series-parallel.
• Diagnose residential and commercial heating control systems.
• Calculate voltage sources, both single-phase and three-phase, including alternators, generators, and batteries.
• Observe National Electric Code compliance, including calculating wire sizes, sizing starters, fuses, and overloads.
• Understand magnetism and magnetic properties.
• Calculate RLC circuits (resistance, inductance, capacitance).
• Calculate power transmission systems (transformers).
• Use programmable logic controllers (PLCs).
• Understand AC motors and alternators, both single- and three-phase.

## SUNY General Education Requirement

Students who intend to receive AA, AS, or baccalaureate degrees must satisfy SUNY and campus General Education (GE) requirements to graduate. Students should be aware that GE requirements may vary by academic program. Consult with your academic advisor for program-specific information; for general information: General Education

AAS and AOS degree students may not be required to fulfill General Education (GE) requirements; however, any student who may wish to transfer should complete as many GE courses as possible. Consult with your academic advisor.

## Technical Standards for Electrical Construction and Instrumentation Programs

The technical standards listed below are intended to inform students of the skills, abilities, and behavioral expectations required in this program. These technical standards reflect performance abilities and characteristics that are necessary to successfully complete the requirements of this program at SUNY Delhi. These standards are not conditions of admission to the program, but persons interested in applying for admission to the program should review this list to develop a better understanding of the skills, abilities, and behavioral expectations necessary to successfully complete the program. The College complies with the requirements and spirit of Section 504 of the Rehabilitation Act and the Americans with Disabilities Act of 1990; therefore, the College will endeavor to make reasonable accommodations for participants with disabilities who are otherwise qualified.

#### Sensory/Observation Skills

General: Use sensory cues to conduct inspections and tests to determine root causes of failures and respond properly.

Specific:

• Interpret read-outs from analog and digital meters, oscilloscopes, tape rulers, and other measuring devices.
• Distinguish identifying colors of wires, push buttons, indicating lights, and other objects.
• Recognize and compare shapes and forms of objects.
• Detect and respond to warning indicators of malfunctions.
• Judge distance and spatial relationships of objects.
• Detect and respond to sensory cues that indicate problems.
• Select appropriate materials, tools and equipment for installation, maintenance and repairs.

#### Motor skills

General: Possess physical strength, flexibility, and dexterity needed to safely perform electrical work.

Specific:

• Operate necessary tools, equipment, and machinery.
• Remove and replace failed components and small parts.
• Position and maneuver in confined spaces.
• Work at varying heights.
• Lift and transport equipment and supplies as necessary.

#### Communication skills

General: Communicate to gather and convey information.

Specific:

• Speak, write, and understand English.
• Obtain necessary information from oral and written sources.
• Express information coherently.
• Document work accurately.

#### Behavioral skills

General: Behave appropriately and safely in a cooperative learning environment.

Specific:

• Fulfill personal and shared responsibilities.
• Work cooperatively with partners and groups.
• Exercise good judgment.
• Distinguish identifying colors of wires, push buttons, indicating lights, and other objects.
• Use a ladder to work at varying heights.
• Document work carefully.

#### Environmental tolerance

General: Function safely in an electrical shop environment.

Specific:

Work for prolonged periods amidst:

• Sharp tools and materials
• Electrical equipment
• Chemicals and toxins
• Heat, dust, and fumes
• Machinery with moving parts
• Slippery or uneven surfaces
• Variations in lighting
• Noise